DESCRIPTION
PERMATEC 1000 is a 100% solids epoxy mortar mix, designed as a
patching or flooring compound. The PERMATEC 1000 system consists of
three components: Resin, Hardener and Blended aggregates.
FUNCTION
PERMATEC 1000 is an excellent flooring and patching material in
areas with heavy traffic, such as forklifts and steel wheeled
carts. PERMATEC 1000 is also an excellent cove base and sloping
material.
TYPICAL
APPLICATIONS
- Warehouse floors
- Food processing plants
- Breweries
- Heavy traffic areas
FEATURES
PERMATEC 1000 is a 100% solids system which exhibits virtually
no shrinkage while maintaining superior impact and abrasion
resistance.
The physical properties of
PERMATEC 1000 are 2-3 times that of standard Portland cement
concrete.
OTHER FEATURES
INCLUDE:
- Rapid cure resulting in
minimal downtime
- Easy to apply
- Virtually odor-free
- Non-skid safety finish (optional)
MIXING
& APPLICATION
FOR 5 AND 22 S.F. KITS
1) Clean the surface making sure that the substrate on which the
product is to be applied is clean, sound and free of all
laitance, dirt, dust, oil, grease, or foreign contaminants.
Mechanical roughening of the substrate or acid etching is
recommended to promote a tenacious bond. If necessary, prime the
surface with a suitable primer.
2) Store product between 65-85oF
and out of direct sunlight. Make certain that the floor
temperature and the air temperature are within the recommended
ranges (65-95oF) before applying the product.
3) Mix part A and part B together
with a Jiffler type mixer on a low speed drill being sure to
scrape the side and bottom of the container. Continue mixing for
another two minutes to insure a homogeneous mix.
4) Mix in the aggregate that is
supplied with the kit until it is completely "wetted
out."
5) Apply the mixed mortar
material at the recommended thickness using a hand trowel.
6) Allow sufficient time for the
material to cure.
7) If you are topcoating PERMATEC
1000, do so within 24 hours to ensure good intercoat adhesion.
Before topcoating, check the base coat for contamination. Clean
or prepare the base coat if necessary before applying a top
coat.
8) Provide for routine
maintenance of your floor to assure years of performance.
|
|
TYPICAL
PROPERTIES
|
| Solids, by
Volume |
|
100% |
|
Compressive
Strength
ASTM C579 |
|
9,500 psi |
|
| Flexural
Strength ASTM D790 |
|
5,500 psi |
|
Tensile
Strength
ASTM D307 |
|
3,000 psi |
|
APPLICATION TEMPERATURE
65-95o F
PACKAGING
& COVERAGE
PERMATEC 1000 is packaged in 5, 22, 110, and 1100 square foot units. Each unit consists Part A (Resin),
Part B (Hardener), and a specially blended aggregate mix.
CURE
TIME
|
Pot Life
(150 grms@70o
F) |
|
30-40 minutes |
|
| Recoat |
|
6-8 hours |
|
| Light Traffic |
|
12-24 hours |
|
| Heavy Traffic |
|
48 hours |
|
SAFETY
PERMATEC 1000 contains blended Epoxies as the resin and blended
Amines as the hardener. Protective clothing and gloves are
recommended to prevent sensitization to these materials. In case
of ingestion or eye contact, contact a physician immediately.
MSDS are available for this product upon request.
WARRANTY
For product warranty see ChemProof Polymers, Inc.
"Standard Limited Warranty." If one is not included
with this literature contact your local distributor or ChemProof
Polymers, Inc. for a copy.
STORAGE
& SHELF LIFE
PERMATEC 1000 should be stored at 50-90o F out of direct
sunlight. All containers should remain unopened until ready for
use. If stored as set out above, PERMATEC 1000 has a minimum
shelf life of one year.
WHERE
PERMATEC 1000 SHOULD NOT BE INSTALLED
PERMATEC 1000 should not be applied over substrates:
- subject to immersion in
aggressive chemicals
- subject to hydrostatic
pressure
- which are unsound
- which are contaminated and
cannot be cleaned
- which are wet during
application
|
